Steel Bifold Specifications
Short Form: Wardrobe and closet doors, so specified to be Slimfold� prefinished metal folding doors manufactured by Slimfold� Products Division, meet or exceed Voluntary Product Standard PS38-70, as published by the U.S. Department of Commerce, National Bureau of Standards.

Full Form: Door panels and reinforcing stiffeners shall be 24-gauge cold rolled steel.

Alternate for coastal areas with high salt content atmosphere: A hot dipped coating of zinc-iron alloy (galvanized) is recommended. Also recommended for bathrooms, laundry rooms, HVAC areas or any highhumidity situation. Contact factory for proper re-painting instructions.

Door panels shall be accurately formed and reinforced with 4" wide stiffeners welded to backs and flanges of panels. Panels shall be hinged in pairs with a minimum of 10" (25.40cm) of piano-type hinges. Panels to be sound-deadened with corrugated fiberboard or absorbent, as option.

All mounting hardware shall be factory installed. Rods to be zinc plated cold rolled steel with yellow dichromate finish. Patented weight bearing pivot rods to be 9/16" (0.79cm) diameter, adjustable screw type, and securely held in position by nylon rod clamp assemblies. Guide rods and upper pivot rods shall be 1/4" (0.64cm) in diameter, spring loaded for easy self-alignment, and securely held in position by selfretaining nylon sleeves. Top and bottom tracks are .05 mill finish aluminum. Pivot sockets and rubber track bumpers shall be adjustable to allow lateral alignment and be preset in the track. Sockets are steel zinc plated and waxed. Doors to be supplied prefinished. Mill finish bottomless track bracket available as an option. Consists of one bracket, socket and mounting screws per two-panel unit. Alignment brackets included on four-panel units. Hardware packages consisting of knobs or pulls, screws, and felt discs to be supplied with each door.

Mirrors shall be high quality, double strength with mylar trimmed edges and shall fully cover the panel. They shall conform to Government Specification DDM- 00411 (b) and be securely mounted with double faced polyurethane tape, which shall also act as a shock absorbing cushion for the glass. Channels shall protect the top and bottom edges of the mirror.

All specifications are based on latest product information available at time of publication approval. We reserve the right to make changes at any time and without notice, in material specifications and styles.

Limited Lifetime Warranty
Slimfold� Products Division warrants to the purchaser that its products, when utilized for interior door use, will be free from defects in materials and workmanship for the life of the product.

Slimfold� Products manufactured with galvanized steel are additionally warranted against rusting for a period of one (1) year from the date of purchase, provided the finish has not been cut or abraded through the metal. Galvanized steel should be used where air has a high salt content or in locations with high humidity; see specifications.

This warranty is applicable only when the products covered by it have been installed in accordance with the recommended written installation instructions of Slimfold� Products Division and with established building practices, have been accorded treatment which is considered good practice in the building industry regarding storage and maintenance, and have been subjected only to normal use. Because Slimfold� Products Division cannot control the manner in which its products are handled after leaving its premises, this warranty does not apply to the finish or other damage occurring during shipment. There are no warranties, express or implied, which extend beyond the description on the face hereof, including the implied warranty of merchantability and the implied warranty of fitness for a particular purpose.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply in some cases. In the event the original consumer purchaser of any Slimfold� product believes that the door or any parts thereof covered by this warranty is defective, a letter outlining the alleged defect should be sent postage prepaid to the following address:

Slimfold� Products Division
PO Box 6416
Dothan, AL 36302

Any Slimfold� Products part covered by this warranty which, upon inspection by an authorized representative of Slimfold� Products Division, are found by said representative to be defective, will be repaired or replaced at the option of Slimfold� Products Division. The purchase price of the part will be refunded and does not include labor, installation costs, finishing costs, shipping costs, or indirect or consequential damages of any nature. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty bestows certain legal rights, and you may also have other rights which vary from state to state.